TM 9-2330-287-14&P
SECTION I
(4) FIG. column. This column lists the number
f. QTY (Column (6)). The QTY (quantity per figure
of the figure where the item is identified/located in
column) indicates the quantity of the item used in the
Section II and Ill.
breakout shown on the illustration figure, which is
prepared for a functional group, subfunctional group, or
(5) ITEM column. The item number is that
an assembly. A "V" appearing in this column in lieu of a
number assigned to the item as it appears in the figure
quantity indicates that the quantity is variable and the
referenced in the adjacent figure number column.
quantity may vary from application to application.
c. FIGURE AND ITEM NUMBER INDEX.
4. Explanation of Columns (Section IV).
(1) FIG. column. This column lists the number
a. NATIONAL STOCK NUMBER (NSN) INDEX.
of the figure where the item is identified/located in
Section II and Ill.
(1) STOCK NUMBER column This column
lists the NSN by National item identification number
(2) ITEM column. The item number is that
(NIIN) sequence. The NIIN consists of the last nine
number assigned to the item as it appears in the figure
NSN
referenced in the adjacent figure number column.
(3) STOCK NUMBER column. This column
digits of the NSN (i.e., 5305-01-674-1467.) When using
lists the NSN for the item.
NllN
(4) FSCM column. The Federal Supply Code
this column to locate an item, ignore the first 4 digits of
for Manufacturer (FSCM) is a 5-digit numeric code
the NSN. However, the complete NSN should be used
used to identify the manufacturer, distributor, or
when ordering items by stock number.
Government agency, etc., that supplies the item.
(2) FIG. column. This column lists the number
(5) PART NUMBER column. Indicates the
of the Figure where the item is identified/located. The
primary number used by the manufacturer (individual,
figures are in numerical order in Section II and Section
firm, corporation, or Government activity), which
Ill.
controls the design and characteristics of the item by
means of its engineering drawings, specifications
(3) ITEM column. The item number identifies
standards, and inspection requirements to identify an
the item associated with the figure listed in the
item or range of items.
adjacent FIG. column. This item is also identified by
the NSN listed on the same line.
5. Special Information.
b. PART NUMBER INDEX. Part numbers in this
Use the following subparagraphs as applicable:
index are listed by part number in ascending
a. USABLE ON CODE. The "USABLE ON CODE
alphanumeric sequence (i.e., vertical arrangement of
letter and number combination which places the first
title appears in the lower right corner of column (6),
Description. Usable on codes are shown in the
letter or digit of each group in order A through Z,
right-hand margin of the description column. uncoded
followed by the numbers 0 through 9 and each
following letter or digit in like order.)
items are applicable to all models. Identification of the
usable on codes used in this publication are:
(1) FSCM column. The Federal Supply Code
Code
for Manufacturer (FSCM) is a 5 digit numeric code
Used On
used to identify the manufacturer, distributor, or
M796
A08
Government agency, etc., that supplies the item.
M796A1
A60
(2) PART NUMBER column. Indicates the
b. FABRICATION INSTRUCTIONS. Bulk materials
primary number used by the manufacturer (individual,
required to manufacture items are listed in the Bulk
firm, corporation, or Government activity), which
Material Functional Group of this RPSTL. Part
controls the design and characteristics of the item by
numbers for bulk materials are also referenced in the
means of its engineering drawings, specifications
description column of the line item entry for the item to
standards, and inspection requirements to identify an
be manufactured/fabricated. Detailed fabrication
item or range of items.
instructions for items source codes to be manufactured
or fabricated are found in Appendix G.
(3) STOCK NUMBER column. This column
lists the NSN for the associated part number and
c. ASSEMBLY INSTRUCTION. Detailed assembly
manufacturer identified in the PART NUMBER and
instructions for items source coded to be assembled
FSCM columns to the left.
from component spare/repair parts are found in
4