TM9-2330-368-14&P
(4) FIG. column. This column lists the
in lieu of a quantity indicates that the quantity is
number of the figure where the item is
variable and the quantity may vary from application to
identified/located in Section II and III.
application.
(5) ITEM column. The item number is that
number assigned to the item as it appears in the figure
F-4. EXPLANATION OF COLUMNS
referenced in the adjacent figure number column,
(SECTION IV)
c. FIGURE AND ITEM NUMBER INDEX,
a. NATIONAL STOCK NUMBER (NSN)
(1) FIG. column. This column lists the
INDEX.
number of the figure where the item is
identified/located in Sections H and 111.
(1) STOCK NUMBER column. This column
(2) ITEM column. The item number is that
lists the NSN by National Item Identification Number
number assigned to the item as it appears in the figure
(NIIN) sequence. The NIIN consists of the last nine
referenced in the adjacent figure number column.
NSN
i
(3) STOCK NUMBER column. This column
digits of the NSN (i.e., 5305-01-674-1467 ). When
lists the NSN for the item.
NIIN
(4) FSCM/CAGEC column. The Federal
using this column to locate an item, ignore the first
Supply Code for Manufacturer (FSCM)/Commercial
4 digits of the NSN. However, the complete NSN
and Government Entity (CAGE) Code (C) is a 5-digit
should be used when ordering items by stock number.
alphanumeric code used to identify the manufacturer,
distributor, or Government agency, etc., that supplies
(2) FIG. column. This column lists the
the item.
number of the figure where the item is
identified/located. The figures are in numerical order
(5) PART NUMBER column. Indicates the
in Section II and Section III.
primary number used by the manufacturer (indi-
vidual, firm, corporation, or Government activity),
(3) ITEM column. The item number identifies
which controls the design and characteristics of the
the item associated with the figure listed in the
item by means of its engineering drawings,
adjacent FIG. column. This item is also identified by
specifications standards and inspection require- ments
the NSN listed on the same line.
to identify an item or range of items.
b. PART NUMBER INDEX. Part numbers in this
F-5. SPECIAL INFORMATION
index are listed by part number in ascending
alphanumeric sequence (i. e., vertical arrangement of
letter and number combination which places the first
a. USABLE ON CODE. The usable on code
letter or digit of each group in order A through Z,
appears in the lower left corner of the Description
followed by the numbers O through 9 and each
column heading. Usable on codes are shown as "UOC:
following letter or digit in like order).
. . . . . . . . . . " in the Description column (justified left)
on the first line following applicable item
(1) FSCM/CAGEC column, The Federal
description/nomenclature. Not Applicable.
Supply Code for Manufacturer (FSCM)/Commercial
and Government Entity (CAGE) Code (C) is a 5-digit
Bulk
b. FABRICATION INSTRUCTIONS.
alphanumeric code used to identify the manufacturer,
materials required to manufacture items are listed in
distributor, or Government agency, etc., that supplies
the Bulk Material Functional Group of this RPSTL.
the item.
Part numbers for bulk materials are also referenced in
the Description column of the line item entry for the
(2) PART NUMBER column. Indicates the
item to be manufactured/fabricated. Detailed
primary number used by the manufacturer (individual,
fabrication instructions for items source coded to be
firm, corporation, or Government activity), which
manufactured or fabricated are found in Appendix G
controls the design and characteristics of the item by
of this manual,
means of its engineering drawings, specifications
INSTRUCTIONS.
Detailed
c. ASSEMBLY
standards, and inspection requirements to identify an
assembly instructions for items source coded to be
item or range of items.
assembled from component spare/repair parts are found
in Chapters 4 and 5 of this manual Items that make up
(3) STOCK NUMBER column. This column
the assembly are listed immediately following the
lists the NSN for the associated part number and
assembly item entry or reference is made to an applicable
manufacturer identified in the PART NUMBER and
figure.
FSCM/CAGEC columns to the left.
F-4
Change 1