* Typical stones are examples only
Sec Stone Selection Chart for specific
Grades and Grits of stone.
LIST OF COMMON MANDRELS, STONES, AND PARTS USED IN WET AND DRY H'1.INNG
WHAT IS NEEDED FOR NORMAL HONING
Minimum
Use
With
Truing
Stone Size
Specific
Size Hole
Mandrel Size
Wedge and Adapter
Sleeve
Use General
or
Purpose
(If required)
Purpose
Stones Examples
R8-120
R8-W
R8-A
TS- 120
1/8" - 9/64"
through
or
or
through
R8 GP
R8 A220S Coarse Grit stone recommended in normal use.
R8-145
K4-W
K4-A
TS-145
--------------------------------------------------------------------------------------------------------------------------
R10-150
R10-W
R10-A
TS-150
5/32" - 11/64" through
or
or
through
R10 GP
R10 A220ES Finishing press fit holes, plastic
R10-180
K5-W
KS-A
TS- 180
--------------------------------------------------------------------------------------------------------------------------
R12-185s
R12-W
R12-A
TS-185
5/16" - 15/64" through
or
or
through
R12 GP
R12 GGZ20M Carbide wear strip inserted in bore, steel
R12-240
K6-W
K6-A
TS-240
--------------------------------------------------------------------------------------------------------------------------
R16-245
R16-W
RP6-A
TS-245
1/4" - 19/64
through
or
or
through
R16 GP
R16 S220M Regular
R16-300
K8 - W
K8 - A
TS-300
Finish piston rod hole
--------------------------------------------------------------------------------------------------------------------------
R20-308
R20-W
R20-A
TS-308
15/16"-23/64" through
or
or
through
R20 GP
R20 AA220S Cast Iron
R20-362
K10-W
K10-A
TS-362
Small bore with hardened sleeve insert
--------------------------------------------------------------------------------------------------------------------------
R24-370
R24-W
R24-A
TS-370
3/8"- 15/32"
through
or
or
through
R24 GP
R24 PA150M Tough chrome steel cylinder liner for
hydraulic
R24-479
K12-W
K1(-A
TS-479
--------------------------------------------------------------------------------------------------------------------------
R32-495
RL32-W
R32-A
TS-495
1/2"- 19/32"
through
or
or
through
R32 GP
R32 A150H Deburr rebuilt actuator cylinder before final
honing
R32-588
K16-W
K16-A
T5-588
--------------------------------------------------------------------------------------------------------------------------
R40-619
R40-W
R40-A
T5-619
5/8" - 3/4"
through
or
or
through
R40 GP
R40 S1011 Grinding hard chrome cylinders
R40-744
K20-W
K20-A
TS-744
--------------------------------------------------------------------------------------------------------------------------
________________________________________________________________________
3/4" - 1"
"B" size
not
R BCD40 TS-1000
1-B
1B A2ZOEH e.g. Roughing in ring scratches
required
or
TS- 1200
2-B
for lubrication
Part No.
K20 (2nd
B-1
R40 choice)
1B A500M e.g. Mirror Polishing
same as above
--------------------------------------------------------------------------------------------------------------------------
1" - 2"
"C" size
not
R BCD40 TS-1200
1-CD
1CD S400S e.g. Polishing Plastic Liners
required
or
TS-1500
2-CD
Part No.
K20 (2nd TS-1700
3-CD
2CD S150M e.g. True up Cast Iron Cylinders
C1-2
R40 choice) TS-2000
4-CD
--------------------------------------------------------------------------------------------------------------------------
1" - 2"
"D" size
not
R BCD40 TS-1500
1-CD
3CD A220H e.g. Hard stones finishing of steel actuator post
required
or
TS-1700
2-CD
Part No.
K20 (2nd TS-2000
3-CD
4CD S320ES e.g. Finish anodized aluminum sleeve
D1.5-2.5
R40 choice) TS-2200
4-CD
TS-2700
5-CD
5CD A280B e.g. Remove roughness on alloy steel cylinder
6-CD
Polish after hardening
--------------------------------------------------------------------------------------------------------------------------
________________________________________________________________________
2-11/16" - 15" CH-6 MASTER Holders
replace Wedges CH - 6
TS - 2750
CAN - 1 roughing
CAN S100M e.g. Roughing Cast
CAN - 533 racks Holder
Universal
CAN - 2 finishing
Iron Cylinders
(Holder Support Support
or
CAN - 3 medium
not needed)
instead of TS - 2700
finishing
CAN A 280EH e.g. Deburring a ring
CAN-543 racks
Adapter
(generally
CAN - 5 polishing
on chrome bore
(Holder Support
otherwise)
CAN - 6 polishing
not needed)
CAN - 7 mirror
CAN S220m e.g. Finishing Cast Iron
CAN-563 racks
Specify
polishing
(CAN - C62
Size
CAN S400ES e.g. Polishing Plated
Holder Support)
Cylinders
CAN-573 racks
(CAN - C82
SCAN A220S e.g. Medium Polishing to aircraft
Holder Support)
hard chrome cylinders
CAN-583 racks
(CAN - C92
Holder Support)
22