TM 9-2330-368-14&P
Direct support or aviation intermediate is
c. FSCM/CAGEC (Column (3)). The Federal
F-
the lowest level than can do complete
Supply Code for Manufacturer (FSCM)/Commercial
repair of the item.
and Government Entity (CAGE) Code (C) is a 5-digit
alphanumeric code which is used to identify the
General support is the lowest level that can
H-
manufacturer, distributor, or Government agency,
do complete repair of the item.
etc., that supplies the item.
L-
Specialized repair activity is the lowest level
d. PART NUMBER (Column (4)). Indicates the
that can do complete repair of the item.
primary number used by the manufacturer (individual,
company, firm, corporation, or Government activity),
Depot is the lowest level that can do
D-
which controls the design and characteristics of the
complete repair of the item.
item by means of its engineering drawings,
Nonreparable. No repair is authorized.
Z-
specifications standards, and inspection requirements
to identify an item or range of items.
No repair is authorized. (No parts or
B-
special tools are authorized for the
NOTE: When you use an NSN to requisition an item,
maintenance of a "B''-coded item.)
the item you receive may have a different part number
However, the item may be reconditioned
from the part ordered.
by adjusting, lubricating, etc., at the user
e. DESCRIPTION AND USABLE ON CODE
level.
(UOC) (Column (5)). This column includes the
(3) Recoverability Code. Recoverability codes
following information:
are assigned to items to indicate the disposition action
(1) The Federal item name and, when
on unserviceable items. The recoverability code is
required, a minimum description to identify the item.
entered in the fifth position of the SMR code as
follows:
(2) Physical security classification. Not
Applicable.
A pplication/Exp lanation
(3) Items that are included in kits and sets are
Z-
Nonreparable item. When unserviceable,
listed below the name of the kit or set on Figure KIT.
condemn and dispose of the item at the
(4) Spare/repair parts that make up an
level of maintenance shown in the 3d
assembled item are listed immediately following the
position of the SMR code.
assembled item line entry.
Reparable item. When uneconomically
O-
(5) Part numbers for bulk materials are
reparable, condemn and dispose of the
referenced in this column in the line item entry for the
item at unit maintenance or aviation unit
item to be manufactured/fabricated.
level.
(6) When the item is not used with all serial
Reparable item. When uneconomically
F-
numbers of the same model, the effective serial
reparable, condemn and dispose of the
numbers are shown on the last line(s) of the
item at the direct support or aviation
description (before UOC).
intermediate level.
(7) The usable on code, when applicable (see
Reparable item. When uneconomically
H-
paragraph 5, Special Information). Not Applicable.
reparable, condemn and dispose of the
item at the general support level.
(8) In the Special Tools List section, the basis
of issue (BOI) appears as the last line(s) in the entry
Reparable item. When beyond lower level
D-
for each special tool, special TMDE, and other special
return to depot.
repair capability,
support equipment. When density of equipments
Condemnation and disposal of item not
supported exceeds density spread indicated in the
authorized below depot level.
basis of issue, the total authorization is increased
Reparable
item.
Condemnation and
L-
proportionately.
disposal of item not authorized below
(9) The statement " END OF FIGURE"
specialized repair activity (SRA).
appears just below the last item description in Column
handling or
Item
requires special
A-
5 for a given figure in both Section H and Section III.
condemnation procedures because of
f. QTY (Column (6)). The QTY (quantity per
specific reasons (e. g., precious metal
figure column) indicates the quantity of the item used
content, high dollar value, critical material,
R e f e r to
in the breakout shown on the illustration figure, which
material).
or
hazardous
is prepared for a functional group, subfunctional
appropriate manuals/directives for specific
group, or an assembly. A "V" appearing in this column
instructions.
Change
1
F-3
