CHAPTER 1 INTRODUCTION - TM-9-2590-209-14-P0014
Tabulated Data..
Figure 1-1. Bulldozer, earth moving: tank mounting, M9 mounted.
Figure 1-3. Special tools.
Table 1-1. Special Tools.
CHAPTER 2 OPERATION INSTRUCTIONS
Operation - TM-9-2590-209-14-P0020
Figure 2-2. Preliminary operating procedures
Figure 2-3. Control positions of blade assembly manual control lever.
Figure 2-4. Operating bulldozer in float position. - TM-9-2590-209-14-P0023
Figure 2-5. Operating bulldozer in hold position. - TM-9-2590-209-14-P0024
Figure 2-6. Removing bulldozer from operation.
Section II. OPERATOR/CREW PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS) - TM-9-2590-209-14-P0026
Table 2-1. Operator/Crew Preventive Maintenance Checks and Services.
Table 2-1. Operator/Crew Preventive Maintenance Checks and Services-Continued
Section III. OPERATION UNDER UNUSUAL CONDITIONS - TM-9-2590-209-14-P0029
Figure 2-7. Emergency lifting cables - stowed on blade assembly.
Figure 2-8. Emergency lifting procedures.
CHAPTER 5 OPERATOR/CREW MAINTENANCE INSTRUCTIONS
BLADE ASSEMBLY FAILS TO RAISE HIGH ENOUGH TO ENGAGE CARRYING HOOKS.
OPERATOR/CREW LUBRICATION GUIDE BULLDOZER, EARTH MOVING: TANK MOUNTING M9
CHAPTER 4 ORGANIZATIONAL MAINTENANCE INSTRUCTIONS - TM-9-2590-209-14-P0035
Figure 4-1. Organizational maintenance lubrication guide (sheet 1 of 2).
Figure 4-1. Organizational maintenance lubrication guide (sheet 2 of 2).
Table 4-1. Organizational Preventive Maintenance Checks and Services Quarterly Schedule
Table 4-1. Organizational Preventive Maintenance Checks and Services Quarterly Schedule (Continued)
Figure 4-2. Removal or installation of headlamp adapter.
Disassembly - TM-9-2590-209-14-P0041
Section IV. Maintenance of Blade Assembly
Installation - TM-9-2590-209-14-P0043
Figure 4-4. Removal or installation of blade assembly (sheet 1 of 2).
Figure 4-4. Removal or Installation of blade assembly (sheet 2 of 2)
Section V. MAINTENANCE OF BLADE ASSEMBLY CUTTING EDGE
Section VI. MAINTENANCE OF PUSHBEAM
Figure 4-7. Removal or installation of pushbeam assemblies.
Section VII. MAINTENANCE OF TILT ARM
Figure 4-8. Removal or installation of tilt arms.
Section VIII. MAINTENANCE OF HYDRAULIC HOSES, TUBES, LINES, AND FITTNGS
Inspection and Repair.
Figure 4-9. Removal or installation of rear tube assemblies (sheet 1 of 3).
Figure 4-9. Removal or installation of rear tube assemblies (sheet 2 of 3).
Figure 4-9. Removal or installation of rear tube assemblies (sheet 3 of 3).
Figure 4-10. Removal or installation of lower hoses, tubes, and guards.
Section IX. MAINTENANCE OF HYDRAULIC CYLINDER ASSEMBLY AND GUARDS
Figure 4-11. Removal or installation of cylinder assembly and guards (sheet 1 of 2).
Figure 4-11. Removal or installation of cylinder assembly and guards (sheet 2 of 2).
Section X. MAINTENANCE OF BLADE AND CYLINDER MOUNTING BRACKETS
Figure 4-12. Removal or installation of blade and cylinder mounting bracket.
Inspection. - TM-9-2590-209-14-P0062
Cleaning and Inspection.
Figure 4-13. Removal or installation of manifold assembly (sheet 1 of 2).
Figure 4-13. Removal or installation of manifold assembly (sheet 2 of 2).
Section XII. MAINTENANCE OF MANIFOLD UNLOADER ASSEMBLY
Section XIII. MAINTENANCE OF MANIFOLD CONTROL VALVE ASSEMBLY
Figure 4-15. Removal or installation of manifold control valve assembly.
Section XIV. MAINTENANCE OF BLADE ASSEMBLY CARRYING HOOKS AND SHAFTS
Figure 4-16. Removal or installation of carrying hooks and shafts.
Section XV. MAINTENANCE OF RESERVOIR
Figure 4-17. Removal or installation of reservoir assembly.
Figure 4-18. Disassembly or assembly of reservoir assembly.
Figure 4-19. Repair of reservoir assembly manifold.
Section XVI. MAINTENANCE OF MAGNETIC CLUTCH
Disassembly - TM-9-2590-209-14-P0076
Figure 4-20. Removal or installation of power takeoff assembly.
Figure 4-21. Disassembly or assembly of power takeoff assembly right-angle drive, magnetic clutch, and hydraulic pump assembly
Section XVII. MAINTENANCE OF POWER TAKEOFF RIGHT-ANGLE DRIVE
Section XVIII. MAINTENANCE OF HYDRAULIC PUMP ASSEMBLY
Removal - TM-9-2590-209-14-P0081
Section XIX. MAINTENANCE OF POWER TAKEOFF SPROCKET ASSEMBLY
Section XX. MAINTENANCE OF BLADE CONTROL LEVER AND LINKAGE
Blade Control Linkage
Figure 4-23. Removal or installation of control Iinkage
Figure 4-24. Removal or installation of bracket and control rods.
Figure 4-25. Removal or installation of guard to manifold.
Figure 4-26. Removal or Installation of control valve linkage.
Installation - TM-9-2590-209-14-P0089
Blade Control Assembly.
Figure 4-28. Removal or installation of blade control assembly.
Section XXI. MAINTENANCE OF ELECTRICAL SYSTEM
Figure 4-29. Removal or Installation of electrical system components (sheet 1 of 2) (M60 only).
Figure 4-29. Removal or installation of electrical system components (sheet 2 of 2) (M60A1, M60AI RISE, M60A3 w/o smoke generator)
Hydraulic Pump Circuit Breaker.
Wiring Harness. - TM-9-2590-209-14-P0096
Figure 4-31. Bulldozer electrical circuit - schematic diagram.
Section XXII. MAINTENANCE OF AIR VENT LINE
Figure 4-32. Removal or installation of hydraulic reservoir air vent line filter and attaching parts.
Section XXIII. TROUBLESHOOTING
Table 4-2. Troubleshooting - TM-9-2590-209-14-P0101
POWER TAKEOFF OVERHEATING.
BLADE ASSEMBLY FAILS TO DIG PROPERLY.
BLADE ASSEMBLY FAILS TO OPERATE
BLADE ASSEMBLY FAILS TO OPERATE - CONTINUED. - TM-9-2590-209-14-P0105
BLADE ASSEMBLY FAILS TO OPERATE - CONTINUED. - TM-9-2590-209-14-P0106
BLADE ASSEMBLY FAILS TO OPERATE - CONTINUED. - TM-9-2590-209-14-P0107
BLADE ASSEMBLY FAILS TO OPERATE - CONTINUED. - TM-9-2590-209-14-P0108
CHAPTER 5 DIRECT AND GENERAL SUPPORT MAINTENANCE INSTRUCTIONS - TM-9-2590-209-14-P0109
Inspection and Repair of Shafts and Splines.
CHAPTER 6 REPAIR INSTRUCTIONS - TM-9-2590-209-14-P0111
Section II. REPAIR OF MAGNETIC CLUTCH
Figure 6-3. Disassembly or assembly of magnetic clutch.
Table 6-1. Repair Standard for Magnetic Clutch
Section III. REPAIR OF HYDRAULIC PUMP ASSEMBLY
Figure 6-5. Disassembly or assembly of hydraulic pump assembly.
Table 6-2. Repair Standards for Hydraulic Pump Assembly
Section IV. REPAIR OF POWER TAKEOFF RIGHT-ANGLE DRIVE
Disassembly - TM-9-2590-209-14-P0119
Figure 6-6. Disassembly or assembly of power takeoff right-angle drive.
Table 6-3. Repair Standards for Power Takeoff Right-Angle Drive
Adjustment - TM-9-2590-209-14-P0122
Section V. REPAIR OF BLADE ASSEMBLY CLYLINDER AND RAM
Table 6-4. Repair Standards for Power Takeoff Right-Angle Drive
Figure 6-8. Disassembly or assembly of blade assembly cylinder and ram.
Assembly - TM-9-2590-209-14-P0126
Figure 6-9. Testing arrangements for hydraulic cylinder and ram.
CHAPTER7 FINAL INSPECTION
CHAPTER 8 REWORK VEHICLE COMPONENTS FOR KIT INSTALLATION
Figure 8-1. Templates and fixtures (sheet 1 of 2).
Figure 8-1. Templates and fixtures (sheet 2 of 2).
Figure 8-2. Rework of transmission shroud for access door opening (early model bulldozer).
Figure 8-3. Hinge build-up and hinge pin reversal.
Figure 8-4. Welding mounting lugs in place (sheet 1 of 2).
Rework of Left Rear Fender
Rework of Left Rear Fender Stowage
Figure 8-8. Rework of master control panel (M60).
Rework of Suspension System.
Figure 8-9. Rework of shock absorber and volute springs. - TM-9-2590-209-14-P0139
Figure 8-9. Rework of shock absorber and volute springs. - TM-9-2590-209-14-P0140
Figure 8-10. Rework of suspension system (sheet 1 of 2).
Figure 8-10. Rework of suspension system (sheet 2 of 2).
Rework of Outrigger and Air Cleaner Box.
Figure 8-11. Rework of outrigger and air cleaner box.
Figure 8-12. Rework of manifold assembly mounting lug.
Figure 8-13. Rework of ram head.
Figure 8-14. Rework of gas particulate precleaner filter assembly.
Figure 8-15. Rework of hydraulic pump control panel bracket (vehicles with smoke generator).
CHAPTER 9
Figure 9-1. Installation of manifold assembly (sheet 1 of 2).
Figure 9-1. Installation of manifold assembly (sheet 2 of 2).
Figure 9-2. Installation of exterior linkage guards.
Figure 9-3. Installation of exterior control assembly.
Section V. INSTALLATION OF BLADE ASSEMBLY MANUAL CONTROL LEVER AND LINKAGE
Figure 9-4. Installation of blade assembly manual control lever and linkage (M60).
Figure 9-5. Installation of blade assembly manual control lever and linkage (M60A1, M60A1 RISE, or M60A3).
Figure 9-6. Installation of power takeoff, sprocket assembly, hoses, and bracket (sheet 1 of 2).
Tubing and Hose Assemblies
Access Plate and Elbows
Figure 9-8. Installation of plates and elbows.
Installation of Armor Tubes and Reservoir
Figure 9-9. Installation of armor tubes and reservoir.
Figure 9-10. Installation of reservoir hoses and guards.
Figure 9-11. Securing components after installation of reservoir, guards, and tubing.
Section VIII. INSTALLATION OF MANFOLD TUBES AND GAURDS
Figure 9-12. Installation of manifold tubes and guards.
Figure 9-13. Installation of tubes and hoses to manifold valve.
Figure 9-14. Alteration and installation of blocks.
Section IX. INSTALLATION OF MOUNTING BRACKETS, CYLINDERS, AND GUARDS
Figure 9-15. Installation of mounting brackets.
Figure 9-16. Installation of cylinder and ram assemblies.
Figure 9-17. Installation of cylinder hoses and guards.
Figure 9-18. Installation of cylinder and guards.
Section X. INSTALLATION OF BLADE ASSEMBLY
Figure 9-19. Installation of blade assembly.
Figure 9-20. Installation of carrying hooks.
Section XII. INSTALLATION OF HEADLAMPS AND GUARDS
Figure 9-21. Installation of headlamps and guards.
Section XIV. HYDRAULIC SYSTEM CHECKOUT PROCEDURES
Figure 9-22. Installation of electrical system (M60).
Figure 9-23. Installation of electrical system (M60A1, M60A1 RISE, and M60A3).
Section XV. INSTALLATION OF RESERVOIR VENT LINE
Figure 9-24. Hydraulic system diagram.
Figure 9-25. Removal of off filter.
Figure 9-26. Installation of reservoir vent line.
Section XVI. INSTALLATION OF GUNNER'S STABILIZATION GUARD
CHAPTER 10 OPERATION AND MAINTENANCE OF PECULIAR COMPONENTS FOR EARLY MODEL M9 BULLDOZER
Section III. OPERATING INDUCTIONS
M9 Bulldozer Operation.
Figure 10-2. Controls (early model bulldozer).
Figure 10-3. Preliminary operating procedure (early model bulldozer).
Figure 10-4. Operating bulldozer in hold position (early model bulldozer).
Figure 10-5. Operating bulldozer in float position (early model bulldozer).
Vehicle Movement.
Figure 10-6. Removing bulldozer from operation (early model bulldozer).
Section IV. OPERATOR/CREW PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS)
Table 10-2. Operator/Crew Preventive Maintenance Checks and Services.
Section V. OPERATOR/CREW MAINTENANCE INSTRUCTIONS
ORGANIZATIONAL MAINTENANCE LUBRICATION GUIDE FOR EARLY MODEL M9 BULLDOZER
Figure 10-7. Lubrication guide for early model M9 bulldozer (sheet 2 of 2).
Table 10-3. Organizational Preventive Maintenance Checks and Services Quarterly Schedule (Early Model Bulldozer).
Figure 10-8. Removal or installation of headlamp adapter (early model bulldozer).
Maintenance of Blade Assembly.
Figure 10-9. Disassembly or assembly of headlamp adapter (early model bulldozer).
Maintenance of Push beam.
Figure 10-10. Removal or Installation of blade assembly (sheet 1 of 2).
Figure 10-10. Removal or installation of blade assembly (sheet 2 of 2)
Figure 10-11. Disassembly or assembly of blade assembly.
Maintenance of Tilt Arm.
Figure 10-12. Removal or installation of pushbeam assemblies.
Figure 10-13. Removal or installation of tilt arms.
Maintenance of Reservoir
Figure 10-14. Removal or installation of reservoir assembly.
Figure 10-15. Disassembly or assembly of reservoir assembly.
Figure 10-16. Repair of reservoir assembly manifold.
Maintenance of Hydraulic Pump and Power Takeoff Group.
Figure 10-17. Removal or installation of hydraulic pump and power takeoff group (early model bulldozer) (sheet 1 of 2).
Figure 10-17. Removal or installation of hydraulic pump and power takeoff group (early model bulldozer) (sheet 2 of 2).
Figure 10-18. Removal or installation of hydraulic mechanical clutch support bracket and yoke assembly.
Adjustment - TM-9-2590-209-14-P0220
Figure 10-19. Removal or installation of mechanical clutch control assembly (early model bulldozer)
Maintenance of Cylinder Assembly Guards.
Figure 10-21. Removal or installation of cylinder guards (sheet 1 of 2).
Figure 10-21. Removal or installation of cylinder guards (sheet 2 of 2).
Maintenance of Hydraulic Cylinder Assembly.
Figure 10-22. Removal or installation of cylinder assembly (sheet 1 of 2).
Figure 10-22. Removal or installation of cylinder assembly (sheet 2 of 2).
Maintenance of Blade Assembly Carrying Hooks and Shafts.
Figure 10-23. Removal or installation of carrying hooks and shafts (sheet 1 of 2).
Table 10-4. Troubleshooting (Early Model Bulldozer)
Section VII. REPAIR INSTRUCTIONS
Figure 10-24. Disassembly or assembly of mechanical clutch assembly and related components (early model bulldozer).
Table 10-5. Repair Standards for Mechanical Clutch and Related Components (Early Model Bulldozer).
Figure 10-25. Disassembly or assembly of blade assembly cylinder and ram.
Table 10-6. Repair Standards for Blade Assembly Cylinder and Ram
Figure 10-26. Testing arrangements for hydraulic cylinder and ram.
Section VIII. REWORK OF VEHICLE COMPONENTS FOR KIT INSTALLATION
Figure 10-27. Rework of transmission shroud for access door opening (early model bulldozer).
Figure 10-28. Installation of hydraulic pump and power takeoff group (early model bulldozer).
Installation of Blade Assembly
Figure 10-29. Installation of clutch control assembly (early model bulldozer).
Figure 10-30. Installation of blade assembly (early model bulldozer).
Figure 10-31. Installation of carrying hooks assembly (early model bulldozer).
Figure 10-32. Installation of headlamps and guards (early model bulldozer).
Installation of Cylinders and Ram Assemblies
Figure 10-34. Installation of cylinders and ram assemblies.
Figure 10-35. Installation of cylinder guards (sheet 1 of 2).
Figure 10-35. Installation of cylinder guards (sheet 2 of 2).
APPENDIX A REFERENCES - TM-9-2590-209-14-P0249
Publications References.
Publications References.- CONT - TM-9-2590-209-14-P0251
Publications References.- CONT - TM-9-2590-209-14-P0252
APPENDIX B COMPONENTS OF END ITEM LIST - TM-9-2590-209-14-P0253
SECTION II INTEGRAL COMPONENTS OF END ITEM
APPENDIX C ADDITIONAL AUTHORIZATION LIST - TM-9-2590-209-14-P0255
APPENDIX D MAINTENANCE ALLOCATION CHART - TM-9-2590-209-14-P0256
Explanation of Columns in the MAC - TM-9-2590-209-14-P0257
Section II. MAINTENANCE ALLOCATION CHART - TM-9-2590-209-14-P0258
Section II. MAINTENANCE ALLOCATION CHART (CONTINUED)
MAINTENANCE ALLOCATION CHART (CONTINUED) - TM-9-2590-209-14-P0260
MAINTENANCE ALLOCATION CHART (CONTINUED) - TM-9-2590-209-14-P0261
Section III. SPECIAL TOOL AND TEST EQUIPMENT REQUIREMENTS
APPENDIX E REPAIR PARTS AND SPECIAL TOOLS LIST
Explanation of Columns. - TM-9-2590-209-14-P0264
Maintenance Code.
Recoverability Code.
How to Locate Repair Parts. - TM-9-2590-209-14-P0267
How to Locate Repair Parts -CONT
Figure E-1. Power takeoff electrical switch, cables, and related parts (sheet 1 of 2).
Figure E-1. Power takeoff electrical switch, cables, and related parts (sheet 2 of 2).
GROUP: 06 ELECTRICAL SYSTEM
GROUP: 0608 POWER TAKE-OFF ELECTRICAL SWITCH, CABLES AND RELATED PARTS
Figure E-2. Headlamp adapter assembly.
GROUP: 0609 HEADLAMP ADAPTER ASSEMBLY
Figure E-3. Torsion bar anchor, volute spring spacer and related parts.
GROUP: 13 WHEELS AND TRACKS
GROUP: 20 POWER TAKE-OFF
GROUP: 2004 POWER TAKE-OFF ASSEMBLY - CONTINUED
Figure E-5. Right-angle drive, clutch, and hydraulic pump, mounting bracket and related parts.
GROUP: 20042 RIGHT-ANGLE DRIVE, CLUTCH, AND HYDRAULIC PUMP, MOUNTING BRACKET AND RELATED PARTS
Figure E-6. Hydraulic right-angle drive magnetic clutch.
GROUP: 20045 HYDRAULIC RIGHT-ANGLE DRIVE MAGNETIC CLUTCH
Figure E-7. Hydraulic pump side mount and sprocket assembly.
GROUP: 20044 HYDRAULIC PUMP SIDE MOUNT AND SPROCKET ASSEMBLY
Figure E-8. Control Linkage.
GROUP: 2006 CONTROL LINKAGE - CONTINUED
Figure E-9. Control handle and linkage.
GROUP: 20061 BULLDOZER CONTROL LEVER AND LINKAGE
Figure E-10. Control valve manifold.
GROUP: 20062 CONTROL VALVE MANIFOLD
Figure E-11. Moldboard mounting brackets and related parts.
GROUP: 20063 MOLDBOARD MOUNTING BRACKETS AND RELATED PARTS
GROUP: 20064 PUSH BEAMS AND RELATED PARTS
Figure E-13. Moldboard, tilt arms, and related parts.
GROUP: 20065 MOLDBOARD, TILT ARMS,
Figure E-14. Moldboard carrying hooks, control handle, and related parts.
GROUP: 20066 MOLDBOARD CARRYING HOOKS,CONTROL HANDLE,AND RELATED PARTS
Figure E-15. Hose guard and valve guard to mounting bracket and manifold.
GROUP: 20067 HOSE GUARD AND VALVE
Figure E-16. Reservoir hoses and guards.
GROUP: 20068 RESERVOIR HOSES AND GUARDS
Figure E-17. Access plate, elbows, and armor tubes.
GROUP: 20069 ACCESS PLATE,ELBOWS, AND ARMOR TUBES
Figure E-18. Cylinder guards.
GROUP: 200610 CYLINDER GUARDS
Figure E-19. Headlamp brush guard.
GROUP: 200611 HEADLAMP BRUSH GUARD
GROUP: 200612 GUNNER'S STABILIZATION GUARD
Figure E-21. Hydraulic pump assembly.
Figure E-22. Hydraulic cylinder and ram assembly.
GROUP: 2407 HYDRAULIC CYLINDER
GROUP: 24071 HYDRAULIC CYLINDER - CONTINUED
Figure E-23. Hose assemblies to elbows.
GROUP: 24072 HOSE ASSEMBLIES TO ELBOWS
GROUP: 2407 TUBES AND HOSES TO MANIFOLD VALVE
GROUP: 2407 TUBES AND HOSES TO MANIFOLD VALVE - CONTINUED
Figure E-25. Reservoir assembly (sheet I of 2).
Figure E-25. Reservoir assembly (sheet 2 of 2).
GROUP: 2408 M9 BULLDOZER RESERVOIR
GROUP: 2408 M9 BULLDOZER RESERVOIR - CONTINUED
GROUP: 26 TOOLS AND TEST EQUIPMENT
Figure E-27. Headlamp adapter assembly (early model bulldozer).
GROUP 06: ELECTRICAL SYSTEM (EARLY MODEL BULLDOZER)
GROUP: 2004 HYDRAULIC PUMP CLUTCH (EARLY MODEL BULLDOZER)
Figure E-29. Clutch control linkage (early model bulldozer).
GROUP: 2004 CLUTCH CONTROL LINKAGE (EARLY MODEL BULLDOZER)
Figure E-30. Right-angle drive, clutch and hydraulic pump mounting bracket and related parts (early model bulldozer).
GROUP: 20041 POWER TAKE-OFF ASSEMBLY (EARLY MODEL BULLDOZER)
GROUP: 20042 RESERVOIR (EARLY MODEL BULLDOZER)
GROUP: 20042 RESERVOIR (EARLY MODEL BULLDOZER) - CONTINUED
GROUP: 2006 PUSH BEAMS AND RELATED PARTS (EARLY MODEL BULLDOZER)
Figure E-33. Moldboard, tilt arms, and related parts (early model bulldozer).
GROUP: 200613 MOLDBOARD, TILT ARMS, AND RELATED PARTS (EARLY MODEL BULLDOZER)
Figure E-34. Moldboard carrying hooks, control handle, and related parts (early model bulldozer).
GROUP: 200614 MOLDBOARD CARRYING HOOKS, CONTROL HANDLE, AND RELATED PARTS (EARLY MODEL BULLDOZER)
Figure E-35. Cylinder guards (early model bulldozer).
GROUP: 200615 CYLINDER GUARDS (EARLY MODEL BULLDOZER)
Figure E-36. Headlamp brush guard (early model bulldozer).
GROUP: 200616 HEADLAMP BRUSH GUARD (EARLY MODEL BULLDOZER)
NATIONAL STOCK NUMBER AND PART NUMBER INDEX - TM-9-2590-209-14-P0346
NATIONAL STOCK NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0347
NATIONAL STOCK NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0348
NATIONAL STOCK NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0349
NATIONAL STOCK NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0350
NATIONAL STOCK NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0351
NATIONAL STOCK NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0352
PART NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS
PART NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0354
PART NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0355
PART NUMBER CROSS-REFERENCE .TO FIGURE AND ITEM NUMBERS - CONTINUEO
PART NUMBER CROSS-R-FERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED
PART NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0358
PART NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0359
PART NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0360
APPENDIX F EXPENDABLE SUPPLIES AND MATERIALS LIST - TM-9-2590-209-14-P0361
Section II EXPENDABLE SUPPLIES AND MATERIALS
TM-9-2590-209-14-P Bulldozer Earth Moving: Tank Mounting M9 (2590-00-708-3563) Manual
Tabulated Data..
Figure 1-1. Bulldozer, earth moving: tank mounting, M9 mounted.
Figure 1-3. Special tools.
Table 1-1. Special Tools.
CHAPTER 2 OPERATION INSTRUCTIONS
Operation - TM-9-2590-209-14-P0020
Figure 2-2. Preliminary operating procedures
Figure 2-3. Control positions of blade assembly manual control lever.
Figure 2-4. Operating bulldozer in float position. - TM-9-2590-209-14-P0023
Figure 2-5. Operating bulldozer in hold position. - TM-9-2590-209-14-P0024
Figure 2-6. Removing bulldozer from operation.
Section II. OPERATOR/CREW PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS) - TM-9-2590-209-14-P0026
Table 2-1. Operator/Crew Preventive Maintenance Checks and Services.
Table 2-1. Operator/Crew Preventive Maintenance Checks and Services-Continued
Section III. OPERATION UNDER UNUSUAL CONDITIONS - TM-9-2590-209-14-P0029
Figure 2-7. Emergency lifting cables - stowed on blade assembly.
Figure 2-8. Emergency lifting procedures.
CHAPTER 5 OPERATOR/CREW MAINTENANCE INSTRUCTIONS
BLADE ASSEMBLY FAILS TO RAISE HIGH ENOUGH TO ENGAGE CARRYING HOOKS.
OPERATOR/CREW LUBRICATION GUIDE BULLDOZER, EARTH MOVING: TANK MOUNTING M9
CHAPTER 4 ORGANIZATIONAL MAINTENANCE INSTRUCTIONS - TM-9-2590-209-14-P0035
Figure 4-1. Organizational maintenance lubrication guide (sheet 1 of 2).
Figure 4-1. Organizational maintenance lubrication guide (sheet 2 of 2).
Table 4-1. Organizational Preventive Maintenance Checks and Services Quarterly Schedule
Table 4-1. Organizational Preventive Maintenance Checks and Services Quarterly Schedule (Continued)
Figure 4-2. Removal or installation of headlamp adapter.
Disassembly - TM-9-2590-209-14-P0041
Section IV. Maintenance of Blade Assembly
Installation - TM-9-2590-209-14-P0043
Figure 4-4. Removal or installation of blade assembly (sheet 1 of 2).
Figure 4-4. Removal or Installation of blade assembly (sheet 2 of 2)
Section V. MAINTENANCE OF BLADE ASSEMBLY CUTTING EDGE
Section VI. MAINTENANCE OF PUSHBEAM
Figure 4-7. Removal or installation of pushbeam assemblies.
Section VII. MAINTENANCE OF TILT ARM
Figure 4-8. Removal or installation of tilt arms.
Section VIII. MAINTENANCE OF HYDRAULIC HOSES, TUBES, LINES, AND FITTNGS
Inspection and Repair.
Figure 4-9. Removal or installation of rear tube assemblies (sheet 1 of 3).
Figure 4-9. Removal or installation of rear tube assemblies (sheet 2 of 3).
Figure 4-9. Removal or installation of rear tube assemblies (sheet 3 of 3).
Figure 4-10. Removal or installation of lower hoses, tubes, and guards.
Section IX. MAINTENANCE OF HYDRAULIC CYLINDER ASSEMBLY AND GUARDS
Figure 4-11. Removal or installation of cylinder assembly and guards (sheet 1 of 2).
Figure 4-11. Removal or installation of cylinder assembly and guards (sheet 2 of 2).
Section X. MAINTENANCE OF BLADE AND CYLINDER MOUNTING BRACKETS
Figure 4-12. Removal or installation of blade and cylinder mounting bracket.
Inspection. - TM-9-2590-209-14-P0062
Cleaning and Inspection.
Figure 4-13. Removal or installation of manifold assembly (sheet 1 of 2).
Figure 4-13. Removal or installation of manifold assembly (sheet 2 of 2).
Section XII. MAINTENANCE OF MANIFOLD UNLOADER ASSEMBLY
Section XIII. MAINTENANCE OF MANIFOLD CONTROL VALVE ASSEMBLY
Figure 4-15. Removal or installation of manifold control valve assembly.
Section XIV. MAINTENANCE OF BLADE ASSEMBLY CARRYING HOOKS AND SHAFTS
Figure 4-16. Removal or installation of carrying hooks and shafts.
Section XV. MAINTENANCE OF RESERVOIR
Figure 4-17. Removal or installation of reservoir assembly.
Figure 4-18. Disassembly or assembly of reservoir assembly.
Figure 4-19. Repair of reservoir assembly manifold.
Section XVI. MAINTENANCE OF MAGNETIC CLUTCH
Disassembly - TM-9-2590-209-14-P0076
Figure 4-20. Removal or installation of power takeoff assembly.
Figure 4-21. Disassembly or assembly of power takeoff assembly right-angle drive, magnetic clutch, and hydraulic pump assembly
Section XVII. MAINTENANCE OF POWER TAKEOFF RIGHT-ANGLE DRIVE
Section XVIII. MAINTENANCE OF HYDRAULIC PUMP ASSEMBLY
Removal - TM-9-2590-209-14-P0081
Section XIX. MAINTENANCE OF POWER TAKEOFF SPROCKET ASSEMBLY
Section XX. MAINTENANCE OF BLADE CONTROL LEVER AND LINKAGE
Blade Control Linkage
Figure 4-23. Removal or installation of control Iinkage
Figure 4-24. Removal or installation of bracket and control rods.
Figure 4-25. Removal or installation of guard to manifold.
Figure 4-26. Removal or Installation of control valve linkage.
Installation - TM-9-2590-209-14-P0089
Blade Control Assembly.
Figure 4-28. Removal or installation of blade control assembly.
Section XXI. MAINTENANCE OF ELECTRICAL SYSTEM
Figure 4-29. Removal or Installation of electrical system components (sheet 1 of 2) (M60 only).
Figure 4-29. Removal or installation of electrical system components (sheet 2 of 2) (M60A1, M60AI RISE, M60A3 w/o smoke generator)
Hydraulic Pump Circuit Breaker.
Wiring Harness. - TM-9-2590-209-14-P0096
Figure 4-31. Bulldozer electrical circuit - schematic diagram.
Section XXII. MAINTENANCE OF AIR VENT LINE
Figure 4-32. Removal or installation of hydraulic reservoir air vent line filter and attaching parts.
Section XXIII. TROUBLESHOOTING
Table 4-2. Troubleshooting - TM-9-2590-209-14-P0101
POWER TAKEOFF OVERHEATING.
BLADE ASSEMBLY FAILS TO DIG PROPERLY.
BLADE ASSEMBLY FAILS TO OPERATE
BLADE ASSEMBLY FAILS TO OPERATE - CONTINUED. - TM-9-2590-209-14-P0105
BLADE ASSEMBLY FAILS TO OPERATE - CONTINUED. - TM-9-2590-209-14-P0106
BLADE ASSEMBLY FAILS TO OPERATE - CONTINUED. - TM-9-2590-209-14-P0107
BLADE ASSEMBLY FAILS TO OPERATE - CONTINUED. - TM-9-2590-209-14-P0108
CHAPTER 5 DIRECT AND GENERAL SUPPORT MAINTENANCE INSTRUCTIONS - TM-9-2590-209-14-P0109
Inspection and Repair of Shafts and Splines.
CHAPTER 6 REPAIR INSTRUCTIONS - TM-9-2590-209-14-P0111
Section II. REPAIR OF MAGNETIC CLUTCH
Figure 6-3. Disassembly or assembly of magnetic clutch.
Table 6-1. Repair Standard for Magnetic Clutch
Section III. REPAIR OF HYDRAULIC PUMP ASSEMBLY
Figure 6-5. Disassembly or assembly of hydraulic pump assembly.
Table 6-2. Repair Standards for Hydraulic Pump Assembly
Section IV. REPAIR OF POWER TAKEOFF RIGHT-ANGLE DRIVE
Disassembly - TM-9-2590-209-14-P0119
Figure 6-6. Disassembly or assembly of power takeoff right-angle drive.
Table 6-3. Repair Standards for Power Takeoff Right-Angle Drive
Adjustment - TM-9-2590-209-14-P0122
Section V. REPAIR OF BLADE ASSEMBLY CLYLINDER AND RAM
Table 6-4. Repair Standards for Power Takeoff Right-Angle Drive
Figure 6-8. Disassembly or assembly of blade assembly cylinder and ram.
Assembly - TM-9-2590-209-14-P0126
Figure 6-9. Testing arrangements for hydraulic cylinder and ram.
CHAPTER7 FINAL INSPECTION
CHAPTER 8 REWORK VEHICLE COMPONENTS FOR KIT INSTALLATION
Figure 8-1. Templates and fixtures (sheet 1 of 2).
Figure 8-1. Templates and fixtures (sheet 2 of 2).
Figure 8-2. Rework of transmission shroud for access door opening (early model bulldozer).
Figure 8-3. Hinge build-up and hinge pin reversal.
Figure 8-4. Welding mounting lugs in place (sheet 1 of 2).
Rework of Left Rear Fender
Rework of Left Rear Fender Stowage
Figure 8-8. Rework of master control panel (M60).
Rework of Suspension System.
Figure 8-9. Rework of shock absorber and volute springs. - TM-9-2590-209-14-P0139
Figure 8-9. Rework of shock absorber and volute springs. - TM-9-2590-209-14-P0140
Figure 8-10. Rework of suspension system (sheet 1 of 2).
Figure 8-10. Rework of suspension system (sheet 2 of 2).
Rework of Outrigger and Air Cleaner Box.
Figure 8-11. Rework of outrigger and air cleaner box.
Figure 8-12. Rework of manifold assembly mounting lug.
Figure 8-13. Rework of ram head.
Figure 8-14. Rework of gas particulate precleaner filter assembly.
Figure 8-15. Rework of hydraulic pump control panel bracket (vehicles with smoke generator).
CHAPTER 9
Figure 9-1. Installation of manifold assembly (sheet 1 of 2).
Figure 9-1. Installation of manifold assembly (sheet 2 of 2).
Figure 9-2. Installation of exterior linkage guards.
Figure 9-3. Installation of exterior control assembly.
Section V. INSTALLATION OF BLADE ASSEMBLY MANUAL CONTROL LEVER AND LINKAGE
Figure 9-4. Installation of blade assembly manual control lever and linkage (M60).
Figure 9-5. Installation of blade assembly manual control lever and linkage (M60A1, M60A1 RISE, or M60A3).
Figure 9-6. Installation of power takeoff, sprocket assembly, hoses, and bracket (sheet 1 of 2).
Tubing and Hose Assemblies
Access Plate and Elbows
Figure 9-8. Installation of plates and elbows.
Installation of Armor Tubes and Reservoir
Figure 9-9. Installation of armor tubes and reservoir.
Figure 9-10. Installation of reservoir hoses and guards.
Figure 9-11. Securing components after installation of reservoir, guards, and tubing.
Section VIII. INSTALLATION OF MANFOLD TUBES AND GAURDS
Figure 9-12. Installation of manifold tubes and guards.
Figure 9-13. Installation of tubes and hoses to manifold valve.
Figure 9-14. Alteration and installation of blocks.
Section IX. INSTALLATION OF MOUNTING BRACKETS, CYLINDERS, AND GUARDS
Figure 9-15. Installation of mounting brackets.
Figure 9-16. Installation of cylinder and ram assemblies.
Figure 9-17. Installation of cylinder hoses and guards.
Figure 9-18. Installation of cylinder and guards.
Section X. INSTALLATION OF BLADE ASSEMBLY
Figure 9-19. Installation of blade assembly.
Figure 9-20. Installation of carrying hooks.
Section XII. INSTALLATION OF HEADLAMPS AND GUARDS
Figure 9-21. Installation of headlamps and guards.
Section XIV. HYDRAULIC SYSTEM CHECKOUT PROCEDURES
Figure 9-22. Installation of electrical system (M60).
Figure 9-23. Installation of electrical system (M60A1, M60A1 RISE, and M60A3).
Section XV. INSTALLATION OF RESERVOIR VENT LINE
Figure 9-24. Hydraulic system diagram.
Figure 9-25. Removal of off filter.
Figure 9-26. Installation of reservoir vent line.
Section XVI. INSTALLATION OF GUNNER'S STABILIZATION GUARD
CHAPTER 10 OPERATION AND MAINTENANCE OF PECULIAR COMPONENTS FOR EARLY MODEL M9 BULLDOZER
Section III. OPERATING INDUCTIONS
M9 Bulldozer Operation.
Figure 10-2. Controls (early model bulldozer).
Figure 10-3. Preliminary operating procedure (early model bulldozer).
Figure 10-4. Operating bulldozer in hold position (early model bulldozer).
Figure 10-5. Operating bulldozer in float position (early model bulldozer).
Vehicle Movement.
Figure 10-6. Removing bulldozer from operation (early model bulldozer).
Section IV. OPERATOR/CREW PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS)
Table 10-2. Operator/Crew Preventive Maintenance Checks and Services.
Section V. OPERATOR/CREW MAINTENANCE INSTRUCTIONS
ORGANIZATIONAL MAINTENANCE LUBRICATION GUIDE FOR EARLY MODEL M9 BULLDOZER
Figure 10-7. Lubrication guide for early model M9 bulldozer (sheet 2 of 2).
Table 10-3. Organizational Preventive Maintenance Checks and Services Quarterly Schedule (Early Model Bulldozer).
Figure 10-8. Removal or installation of headlamp adapter (early model bulldozer).
Maintenance of Blade Assembly.
Figure 10-9. Disassembly or assembly of headlamp adapter (early model bulldozer).
Maintenance of Push beam.
Figure 10-10. Removal or Installation of blade assembly (sheet 1 of 2).
Figure 10-10. Removal or installation of blade assembly (sheet 2 of 2)
Figure 10-11. Disassembly or assembly of blade assembly.
Maintenance of Tilt Arm.
Figure 10-12. Removal or installation of pushbeam assemblies.
Figure 10-13. Removal or installation of tilt arms.
Maintenance of Reservoir
Figure 10-14. Removal or installation of reservoir assembly.
Figure 10-15. Disassembly or assembly of reservoir assembly.
Figure 10-16. Repair of reservoir assembly manifold.
Maintenance of Hydraulic Pump and Power Takeoff Group.
Figure 10-17. Removal or installation of hydraulic pump and power takeoff group (early model bulldozer) (sheet 1 of 2).
Figure 10-17. Removal or installation of hydraulic pump and power takeoff group (early model bulldozer) (sheet 2 of 2).
Figure 10-18. Removal or installation of hydraulic mechanical clutch support bracket and yoke assembly.
Adjustment - TM-9-2590-209-14-P0220
Figure 10-19. Removal or installation of mechanical clutch control assembly (early model bulldozer)
Maintenance of Cylinder Assembly Guards.
Figure 10-21. Removal or installation of cylinder guards (sheet 1 of 2).
Figure 10-21. Removal or installation of cylinder guards (sheet 2 of 2).
Maintenance of Hydraulic Cylinder Assembly.
Figure 10-22. Removal or installation of cylinder assembly (sheet 1 of 2).
Figure 10-22. Removal or installation of cylinder assembly (sheet 2 of 2).
Maintenance of Blade Assembly Carrying Hooks and Shafts.
Figure 10-23. Removal or installation of carrying hooks and shafts (sheet 1 of 2).
Table 10-4. Troubleshooting (Early Model Bulldozer)
Section VII. REPAIR INSTRUCTIONS
Figure 10-24. Disassembly or assembly of mechanical clutch assembly and related components (early model bulldozer).
Table 10-5. Repair Standards for Mechanical Clutch and Related Components (Early Model Bulldozer).
Figure 10-25. Disassembly or assembly of blade assembly cylinder and ram.
Table 10-6. Repair Standards for Blade Assembly Cylinder and Ram
Figure 10-26. Testing arrangements for hydraulic cylinder and ram.
Section VIII. REWORK OF VEHICLE COMPONENTS FOR KIT INSTALLATION
Figure 10-27. Rework of transmission shroud for access door opening (early model bulldozer).
Figure 10-28. Installation of hydraulic pump and power takeoff group (early model bulldozer).
Installation of Blade Assembly
Figure 10-29. Installation of clutch control assembly (early model bulldozer).
Figure 10-30. Installation of blade assembly (early model bulldozer).
Figure 10-31. Installation of carrying hooks assembly (early model bulldozer).
Figure 10-32. Installation of headlamps and guards (early model bulldozer).
Installation of Cylinders and Ram Assemblies
Figure 10-34. Installation of cylinders and ram assemblies.
Figure 10-35. Installation of cylinder guards (sheet 1 of 2).
Figure 10-35. Installation of cylinder guards (sheet 2 of 2).
APPENDIX A REFERENCES - TM-9-2590-209-14-P0249
Publications References.
Publications References.- CONT - TM-9-2590-209-14-P0251
Publications References.- CONT - TM-9-2590-209-14-P0252
APPENDIX B COMPONENTS OF END ITEM LIST - TM-9-2590-209-14-P0253
SECTION II INTEGRAL COMPONENTS OF END ITEM
APPENDIX C ADDITIONAL AUTHORIZATION LIST - TM-9-2590-209-14-P0255
APPENDIX D MAINTENANCE ALLOCATION CHART - TM-9-2590-209-14-P0256
Explanation of Columns in the MAC - TM-9-2590-209-14-P0257
Section II. MAINTENANCE ALLOCATION CHART - TM-9-2590-209-14-P0258
Section II. MAINTENANCE ALLOCATION CHART (CONTINUED)
MAINTENANCE ALLOCATION CHART (CONTINUED) - TM-9-2590-209-14-P0260
MAINTENANCE ALLOCATION CHART (CONTINUED) - TM-9-2590-209-14-P0261
Section III. SPECIAL TOOL AND TEST EQUIPMENT REQUIREMENTS
APPENDIX E REPAIR PARTS AND SPECIAL TOOLS LIST
Explanation of Columns. - TM-9-2590-209-14-P0264
Maintenance Code.
Recoverability Code.
How to Locate Repair Parts. - TM-9-2590-209-14-P0267
How to Locate Repair Parts -CONT
Figure E-1. Power takeoff electrical switch, cables, and related parts (sheet 1 of 2).
Figure E-1. Power takeoff electrical switch, cables, and related parts (sheet 2 of 2).
GROUP: 06 ELECTRICAL SYSTEM
GROUP: 0608 POWER TAKE-OFF ELECTRICAL SWITCH, CABLES AND RELATED PARTS
Figure E-2. Headlamp adapter assembly.
GROUP: 0609 HEADLAMP ADAPTER ASSEMBLY
Figure E-3. Torsion bar anchor, volute spring spacer and related parts.
GROUP: 13 WHEELS AND TRACKS
GROUP: 20 POWER TAKE-OFF
GROUP: 2004 POWER TAKE-OFF ASSEMBLY - CONTINUED
Figure E-5. Right-angle drive, clutch, and hydraulic pump, mounting bracket and related parts.
GROUP: 20042 RIGHT-ANGLE DRIVE, CLUTCH, AND HYDRAULIC PUMP, MOUNTING BRACKET AND RELATED PARTS
Figure E-6. Hydraulic right-angle drive magnetic clutch.
GROUP: 20045 HYDRAULIC RIGHT-ANGLE DRIVE MAGNETIC CLUTCH
Figure E-7. Hydraulic pump side mount and sprocket assembly.
GROUP: 20044 HYDRAULIC PUMP SIDE MOUNT AND SPROCKET ASSEMBLY
Figure E-8. Control Linkage.
GROUP: 2006 CONTROL LINKAGE - CONTINUED
Figure E-9. Control handle and linkage.
GROUP: 20061 BULLDOZER CONTROL LEVER AND LINKAGE
Figure E-10. Control valve manifold.
GROUP: 20062 CONTROL VALVE MANIFOLD
Figure E-11. Moldboard mounting brackets and related parts.
GROUP: 20063 MOLDBOARD MOUNTING BRACKETS AND RELATED PARTS
GROUP: 20064 PUSH BEAMS AND RELATED PARTS
Figure E-13. Moldboard, tilt arms, and related parts.
GROUP: 20065 MOLDBOARD, TILT ARMS,
Figure E-14. Moldboard carrying hooks, control handle, and related parts.
GROUP: 20066 MOLDBOARD CARRYING HOOKS,CONTROL HANDLE,AND RELATED PARTS
Figure E-15. Hose guard and valve guard to mounting bracket and manifold.
GROUP: 20067 HOSE GUARD AND VALVE
Figure E-16. Reservoir hoses and guards.
GROUP: 20068 RESERVOIR HOSES AND GUARDS
Figure E-17. Access plate, elbows, and armor tubes.
GROUP: 20069 ACCESS PLATE,ELBOWS, AND ARMOR TUBES
Figure E-18. Cylinder guards.
GROUP: 200610 CYLINDER GUARDS
Figure E-19. Headlamp brush guard.
GROUP: 200611 HEADLAMP BRUSH GUARD
GROUP: 200612 GUNNER'S STABILIZATION GUARD
Figure E-21. Hydraulic pump assembly.
Figure E-22. Hydraulic cylinder and ram assembly.
GROUP: 2407 HYDRAULIC CYLINDER
GROUP: 24071 HYDRAULIC CYLINDER - CONTINUED
Figure E-23. Hose assemblies to elbows.
GROUP: 24072 HOSE ASSEMBLIES TO ELBOWS
GROUP: 2407 TUBES AND HOSES TO MANIFOLD VALVE
GROUP: 2407 TUBES AND HOSES TO MANIFOLD VALVE - CONTINUED
Figure E-25. Reservoir assembly (sheet I of 2).
Figure E-25. Reservoir assembly (sheet 2 of 2).
GROUP: 2408 M9 BULLDOZER RESERVOIR
GROUP: 2408 M9 BULLDOZER RESERVOIR - CONTINUED
GROUP: 26 TOOLS AND TEST EQUIPMENT
Figure E-27. Headlamp adapter assembly (early model bulldozer).
GROUP 06: ELECTRICAL SYSTEM (EARLY MODEL BULLDOZER)
GROUP: 2004 HYDRAULIC PUMP CLUTCH (EARLY MODEL BULLDOZER)
Figure E-29. Clutch control linkage (early model bulldozer).
GROUP: 2004 CLUTCH CONTROL LINKAGE (EARLY MODEL BULLDOZER)
Figure E-30. Right-angle drive, clutch and hydraulic pump mounting bracket and related parts (early model bulldozer).
GROUP: 20041 POWER TAKE-OFF ASSEMBLY (EARLY MODEL BULLDOZER)
GROUP: 20042 RESERVOIR (EARLY MODEL BULLDOZER)
GROUP: 20042 RESERVOIR (EARLY MODEL BULLDOZER) - CONTINUED
GROUP: 2006 PUSH BEAMS AND RELATED PARTS (EARLY MODEL BULLDOZER)
Figure E-33. Moldboard, tilt arms, and related parts (early model bulldozer).
GROUP: 200613 MOLDBOARD, TILT ARMS, AND RELATED PARTS (EARLY MODEL BULLDOZER)
Figure E-34. Moldboard carrying hooks, control handle, and related parts (early model bulldozer).
GROUP: 200614 MOLDBOARD CARRYING HOOKS, CONTROL HANDLE, AND RELATED PARTS (EARLY MODEL BULLDOZER)
Figure E-35. Cylinder guards (early model bulldozer).
GROUP: 200615 CYLINDER GUARDS (EARLY MODEL BULLDOZER)
Figure E-36. Headlamp brush guard (early model bulldozer).
GROUP: 200616 HEADLAMP BRUSH GUARD (EARLY MODEL BULLDOZER)
NATIONAL STOCK NUMBER AND PART NUMBER INDEX - TM-9-2590-209-14-P0346
NATIONAL STOCK NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0347
NATIONAL STOCK NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0348
NATIONAL STOCK NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0349
NATIONAL STOCK NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0350
NATIONAL STOCK NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0351
NATIONAL STOCK NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0352
PART NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS
PART NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0354
PART NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0355
PART NUMBER CROSS-REFERENCE .TO FIGURE AND ITEM NUMBERS - CONTINUEO
PART NUMBER CROSS-R-FERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED
PART NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0358
PART NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0359
PART NUMBER CROSS-REFERENCE TO FIGURE AND ITEM NUMBERS-CONTINUED - TM-9-2590-209-14-P0360
APPENDIX F EXPENDABLE SUPPLIES AND MATERIALS LIST - TM-9-2590-209-14-P0361
Section II EXPENDABLE SUPPLIES AND MATERIALS
TM-9-2590-209-14-P Bulldozer Earth Moving: Tank Mounting M9 (2590-00-708-3563) Manual
