TM 9-2330-356-14
(4) Disassembly of Frame.
(k) Remove six screws (44) and lockwashers
(45) securing the ring gear (46) to the disc (47). Remove six
spacers (48) and ring gear (46). Remove six capscrews (49)
NOTE
and shakeproof washers (50), and remove bevel gear (51),
Drum and motor must be removed before
complete disassembly of frame can be
(2) Removal of Motor.
accomplished.
NOTE
(a) Remove four capscrews (66), washers
(67), lockwashers (68), and nuts (69). Remove two tie rods
Hose reel need not be removed from cabinet
(70).
to remove motor.
(b) R e m o v e e i g h t c a p s c r e w s ( 7 1 ) ,
lockwashers (68), and nuts (69). Remove two side angles
(a) Remove four machine screws (52) and
(72).
then remove cover (53). Tag and disconnect electrical
leads from motor (54) at the motor junction box (55) and
39. Set screw
1. Capscrew (2)
the motor junction box from bushing (56) and bushing
40. Support collar
2. Lockwasher (2)
from motor.
41. Capscrew (6)
3. Flatwasher (2)
42. Nut (6)
4. Pinion guard
43. Lockwashers (6)
5. Pinion bearing assembly
WARNING
44. Screw (6)
6. Front frame
45. Lockwasher (6)
7. Capscrew (2)
46. Ring gear
8. Flatwasher (2)
Do not remove nipple from motor. Nipple is
47. Disc
9. Lockwasher (2)
packed in place with plaster. if nipple is
48. Spacer (6)
10. Nut (2)
removed, motor will no longer be explosion
49. Screw (6)
11. Capscrew (2)
proof. Failure to follow this warning may
50. Shakeproof washers (6)
12. Flatwasher (2)
result in serious injury or death to personnel.
51. Bevel gear
13. Lockwasher (2)
52. Machine screw (4)
14. Nut (2)
53. Cover
15. Rear frame
(b) Remove four screws (57), lockwashers
54. Motor
16. Spacer
55. Motor junction box
(58), and nuts (59) securing motor (54) to mounting
17. Bearing and collar
56. Bushing
18. Stud (4)
bracket (60) and to frame (6). Remove motor (54).
57, Screw (4)
19. Set screw
58. Lockwasher (4)
20. Disc
(c) Loosen set screw (61) and remove pinion
59. Nut (4)
21. Capscrew (6)
gear (62).
60. Mounting bracket
22. Lockwasher (6)
61. Set screw
23. Nut (6)
62. Pinion gear
24. Collar
(3) Removal of Terminal Board in Motor Junction
63. Terminal board
25. Thrust washer (as req'd)
Box.
64. Capacitor (2)
26. Drum
65. Machine screw (2)
27. Stud (4)
(a) If motor was not previously removed
66. Capscrew (4)
28. Spacer (4)
under paragraph (2) above, remove the four machine
67. Washer (4)
29. Adapter elbow
68. Lockwasher (12)
30. Swing joint
screws (52) and cover (53). Remove two leads with
69. Nut (4)
31. Capscrew
terminals (11, fig. 8-7) that come from motor at the
70. Tie rod (2)
32. Lockwasher
terminal board. Tag and disconnect all electrical leads
71. Capscrew (8)
33. Nut
72. Side angle (2)
34. Axle shaft
capacitors (64).
73. Nut (6)
35. Capscrew (4)
74. Lockwasher (6)
36. Lockwasher (4)
75. Nut (6)
(b) Remove the two machine screws (65)
37. Outlet elbow
76. Lockwasher (6)
38. O-ring
securing the terminal board (63) to the junction box and
remove the terminal board.
8-12