TM 9-3405-206-14 & P
14" METAL CUTTING BAND SAW
as woods and plastics.
This Band saw incorporates a modern drive with a clutch that permits
instant changes from direct gear drive (or vice versa) by the simple
shift of a knob. V-belts are not disturbed.
This unit can be used to handle both wood and metal cutting jobs.
Overall Dimensions:
65 1 2 " (1663.7 mm)
Height (On stand).....................................
Width .......................................................
25" (635 mm)
17 1 2 (444.5 mm)
Front to Rear............................................
Capacities:
13 3 4 " (349.2 mm)
Blade to Frame ........................................
6 1 4 " (158.7 mm)
Under Guide and Wheel...........................
Under Guide and Wheel
12 1 4 (311.1 mm)
(With 28-984 Height Attachment) .........
Speeds:
With 1725 RPM Motor40,60,85,160,220,335,3000
SFM (12,192; 18,288; 25,908;
35,052; 48,768; 67,056; 102,108;
914,400 Surf. MM/Min.)
Table:
Size..........................................
14X14" (355.6 x355.6 mm)
24-Volt Safety Con-
3 " (9.5 mm) Deep by 3 (19.05 mm) Wide
Grove ...............
trol System
14" Metal
8
4
Cutting Band saws offer a low 24 volts at the push
Tilt to Right...........
45; to Left ............................................
10'
button control station for extra operator safety.
42 3 4 " (1085.8 mm)
Height From Floor ....................................
Magnetic control system provides on-off control,
low-voltage, no-voltage (when power is interrupted,
Blade:
machine can be started only by pressing start
3 " (19.05 mm)
Width: Maximum .....................................
4
button), and motor overload protection. On three
Length: Maximum ...................................
94" (2387.6 mm)
phase systems, overload protection is provided on
all three legs.
Shrouded green start button
91 1 2 " (2324.1 mm)
Minimum ....................................
prevents accidental starts while protruding red stop
93 1 2 " (2374.9 mm)
Standard ....................................
button is extra large for quick, emergency stops.
Switch cover and buttons are made of non-
Length (With 28-984 Height Attachment):
conductive material for added safety.
Maximum .................................................
106" (2692.4 mm)
103 1 2 " (2628.9 mm)
Minimum ..................................................
Basic Machine Without Stand: includes wheel
and blade guards, 7" arbor pulley for wood cutting, No. 41-724 4-step
Standard ..................................................
105" (2667 mm)
arbor pulley ( 3 4 " bore) for metal cutting, 3 4 " to 5 8 " and 3 4 to 1 2 "
No. 28-300 Basic Machine Without Stand: 14: metal cutting band
reducing, bushings for 3 4 " bore 4-step motor pulley, 49-111 (set of 2)
saw with wheel and blade guards, 7" arbor pulley for wood cutting, 41-
724 4-step arbor pulley, (with 3 4 " bore), for metal cutting 3 4 " to 5 8 "
matched V-belts, 41-714 motor pulley ( 3 4 " bore), blade guides and
and 3 4 " to 1 2 " reducing bushings for motor pulley, 49-111 (set of
No. 28-062 (old 1062) metal cutting blade.
This 14" metal cutting band saw has eight cutting speeds 40 to 3000
two) matched V-belts, 41-714 4-stop motor pulley (with 3 4 " bore),
FPM using a standard motor. There is low band saw speed -40 FPM.
There are eight speeds -40, 60, 85, 115, 160, 220 or 335 FPM for
blade guides and 28-062 (old 1062) metal cutting blade. Without
metal cutting and a high speed of 3000 FPM for wood cutting. It cuts
stand, motor or switch, 168 lbs.
stainless steel, armor plate, high speed steel, alloy steel, cast iron,
No. 50-122 Enclosed Steel Stand. Includes 50-139 basic stand, 50-
transite
and
other
materials
136 motor plate and 50-135 belt guard, 54 lbs.
Note:
See Section J7 for Band Saw
Accessories.
ENCLOSED STEEL STAND WITH BELT GUARD, MOTOR AND CONTROLS (Factory Mounted and Wired)
Note: Enclosed Steel Stands With Electricals Can Be Ordered Either With or Without the Basic No. 28-300
14" Band Saw.
MOTOR
MOTOR CONTROL
MOTOR
HERTZ AND
MOTOR
SHIPPING
CATALOG
CAT. NO.
ENCLOSURE
MOTOR RPM
VOLTAGE
WT., LBS
NUMBER
200V
Single Phase,
Push Button Switch Only
TEFC
60-1725
115/230
80
49-963
24V Push Button Station, Magnetic Starter,
TEFC
60-1725
115/230
81
49-964
2
Three Phase,
24V Push Button Station, Magnetic Starter
TEFC
60-1725
230/460
94
49-972
52-113
2
3