TM 9-2330-356-14
(4) Disassembly of Frame.
(52), and nuts (53) securing the collar (47) to the disc (46).
Remove the collar.
NOTE
Drum and motor must be removed before
(2) Removal of Motor.
complete disassembly of frame can be
accomplished.
NOTE
(a) Remove four capscrews (68), washers
(69), lockwashers (70), and nuts (71). Remove two tie rods
Hose reel need not be removed from cabinet
(72).
to remove motor.
(b) Remove eight capscrews (73), lock-
washers (70), and nuts (71). Remove two side angles (74).
(a) Remove four machine screws (54).
Remove cover (55). Tag and disconnect electrical leads
Legend for figure 8-6:
from motor (56) at the motor junction box (57), and
remove all conduit connections (para 4-27). Disconnect
40. Capscrew (4)
1. Capscrew (2)
the motor junction box from bushing (58) and bushing
41. Lockwasher (4)
2. Lockwasher (2)
from motor.
42. Outlet adapter
3. Flatwasher (2)
43. O-ring
4. Spacer
44. Set screw
5. Pinion bearing assembly
WARNING
45. Bearing and collar
6. Front frame
46. Disc
7. Capscrew (2)
47. Collar
8. Flatwasher (2)
DO NOT remove nipple from motor. Nipple is
48. Drum
9. Lockwasher (2)
packed in place with plaster. If nipple Is
49. Stud (6)
removed, motor will no longer be explosion
10. Nut (2)
50. Thrust washer (as req'd)
proof. Failure to follow this warning may
11. Capscrew (2)
result in serious injury or death to personnel.
51. Capscrew (6)
12. Flatwasher (2)
52. Lockwasher (6)
13. Lockwasher (2)
53. Nut (6)
14. Nut (2)
(b) Remove four screws (59), lockwashers
54. Machine screw (4)
15. Rear frame
.(60), and nuts (61) securing motor (56) to mounting
55. Cover
16, Spacer
bracket (62) and to frame (6). Remove motor (56).
56. Motor
17. Spacer
57. Motor junction box
18. Capscrew (6)
58. Bushing
19. Lockwasher (6)
(c) Remove two screws (59), lockwashers
59. Screw (6)
20. Swivel joint
(60), and nuts (61). Remove mounting bracket (62).
60. Lockwasher (6)
21. O-ring
61. Nut (6)
22. Disc
(d) Loosen set screw (63) and remove pinion
62. Mounting bracket
23. Stud (6)
gear (64).
63. Set screw
24. Spacer (6)
64. Pinion gear
25. Screw (6)
(3) Removal of Terminal Board in Motor Junction
65. Terminal board
26. Lockwasher (6)
Box.
66. Capacitor (2)
27. Ring gear
67. Machine screw (2)
28. Spacer (6)
(a) If motor was not previously removed
68. Capscrew (4)
29. Capscrew (6)
under paragraph (2) above, remove the four machine
69. Washer (4)
30. Bevel gear
screws (54) and cover (55). Remove two leads with
70. Lockwasher (12)
31. Capscrew
terminals (11, fig. 8-7) that come from motor at the
71. Nut (12)
32. Lockwasher
terminal board. Tag and disconnect all electrical leads
72. Tie rod (2)
33. Nut
from the terminal board (65) (para 4-27). Remove the two
73. Capscrew (8)
34. Adapter elbow
capacitors (66).
74, Side angle (2)
35. Axle shaft
75. Pinion guard
36. Capscrew (4)
76. Nut (6)
37. Lockwasher (4)
(b) Remove the two machine screws (67)
77. Lockwasher (6)
38. Outlet elbow
securing the terminal board (65) to the junction box and
78. Nut (6)
39. O-ring
remove the terminal board.
8-8
