TM 9-2330-356-14
(4) Drum Assembly.
capscrews (1), lockwashers (2), and flatwashers (3). Ensure
that pinion-on-pinion bearing assembly (5) mates properly
(a) Using six capscrews (51), lockwashers
with bevel gear (30).
(52), and nuts (53), fasten the collar (47) to the disc (46).
e.
NOTE
Hose Reel - 1 and 1-inch (Fig. 8-8)
Install original number of thrust washers that
were removed at disassembly.
a.
Disassembly (Fig. 8-8).
(b) Install six spacers (24) and thrust b.
washers (50) `to disc (46). Secure with `six nuts (78),
(1) Drum Assembly.
lockwashers (77), and studs (49).
(a) Remove two capscrews (1), lockwashers
(c) Install bearing and collar (45) onto rude
(2), and flatwashers (3) securing the pinion bearing
shaft (35). Rotate collar counterclockwise to lock bearing
assembly (hose reel lock) (5) to the frame (6). Remove the
and collar on axle shaft. Install axle shaft through collar
pinion bearing assembly (5) and the guard (4).
(47) until bearing and collar (45) is against collar (47).
Tighten set screw (44).
(b) Attach a suitable hoist to drum (26), and
remove the two capscrews (7), flatwashers (8),
(d) Assemble the outlet elbow (38) by
lockwashers (9), and nuts (10). Then remove two
installing a new O-ring (43) between the outlet elbow (38)
capscrews (11), flatwashers (12), lockwashers (13), and
and the outlet adapter (42). Use four capscrews (40) and
nuts (14). Lift drum assembly from front and rear frame (6
lockwashers (41) to secure the outlet elbow (38) and outlet
and 15) and place on a suitable work bench. Be sure to
adapter together. Assemble the outlet elbow (38) to the
keep the two spacers (16) with the drum assembly.
adapter elbow (34) by installing a new O-ring (39) between
the outlet elbow (38) and the adapter elbow (34). Use four
(c) Loosen set screw on bearing collar. Use
capscrews (36) and lockwashers (37) to secure the two
punch to rotate collar clockwise to release bearing and
elbows (34 and 38) together.
collar from shaft.
(e) Install the drum (48) over the six spacers
(d) Remove four nuts (73), lockwashers (74),
(24). Install the adapter elbow (34) onto axle shaft (35).
and studs (18) from disc (20). Remove six capserews (21),
Install the capscrew (31), lockwasher (32), and nut (33).
lockwashers (22), and nuts (23). Remove collar (24).
(f) Position the bevel gear (30) on disc (22)
(e) Remove drum (26).
and secure with six capscrews (29).
NOTE
(g) Position the ring gear (27) and six spacers
(28) on the disc (22), and secure with six screws (25) and
Take note of how many thrust washers (25)
lockwashers (26).
are used between spacers and disc.
(h) Install the disc (22) onto the six spacers
(24) by securing with six studs (23), lockwashers (77), and
(f) Remove four nuts (75), lockwashers (76),
nuts (78).
studs (27), thrust washers (25), and spacers (28).
(i) Put a new O-ring (21) between the
(g) Unscrew adapter elbow (29) from the
adapter elbow (34) and the swivel joint (20), and fasten the
swing joint (30).
elbow and swivel joint together with six capscrews (18) and
(h) Remove capscrew (31), lockwasher (32),
lockwashers (19).
and nut (33). Remove axle shaft (34). Remove four
(j) Attach a suitable hoist to the drum (48)
capscrews (35) and lockwashers (36) securing outlet elbow
and raise drum to position over frame. Install spacers (16
(37) to adapter elbow (29). Remove outlet elbow (37) and
and 17) between bearing and collar (45) and frame (15).
O-ring (38). Discard O-ring.
Install two capscrews (7), flat washers (8), lockwashers (9),
(i) Loosen set screw (39) and remove swing
and nuts (10). Next, install two capscrews (11), flat washers
(12), lockwashers (13), and nuts (14).
joint (30) from the support collar (40).
(j) Remove six capscrews (41), lockwashers
(k) Position spacer (4) and pinion and
bearing assembly (5) onto frame (6), and secure with two
(43), and nuts (42). Remove support collar (40).
