TM 9-2330-356-14
c.
Cleaning, Inspection, and Repair.
(d) Reconnect hose reel wiring in motor
(e) Replace motor junction box cover (53,
WARNING
fig. 8-8) and secure in place
with four machine screws (52).
Dry cleaning solvent P-D-680 is toxic and
flammable. Always wear protective goggles
and gloves, and use only in a well-ventilated
area. Avoid contact with skin, eyes, and
NOTE
clothes, and DO NOT breathe vapors. DO
Be sure pinion gear teeth mesh properly with
NOT use near open flame or excessive heat.
the ring gear teeth.
The solvent's flash point is 100F-138F
(38C-59C). if you become dizzy while
(a) Install pinion gear (62) on motor shaft.
using cleaning solvent, immediately get fresh
Tighten set screw (61).
air and medical help. If solvent contacts eyes,
immediately wash your eyes with water and
(b) Position motor between mounting
get medical aid.
bracket (60, fig. 8-8) and frame (6). Install four capscrews
(1) Clean all metal parts with dry cleaning
(c) Install bushing (56) into junction box
(55). Install assembly onto motor.
(2) Inspect gears for worn, damaged, or missing
teeth. Replace gears if damaged.
(d) Connect the two motor leads to the
terminal board (63) in the junction box. Connect leads to
d.
cover (53) and secure with four machine screws (52).
(1) Assembly of Frame.
(4) Drum Assembly.
(a) Position one side angle (72) onto the two
frames (6 and 15). Secure in place with four capscrews
(47) with six screws (49) and shakeproof washers (50).
Attach ring gear (46) to disc (47). Use six spacers (48)
between the ring gear and disc, and secure with six screws
(b) Install other side angle (72) onto the two
(44) and lockwashers (45).
frames (6 and 15). Secure in place with four capscrews
(b) Position the support collar (40) on disc
(47), and secure with six capscrews (41), lockwashers (43),
(c) Install both tie rods (70) onto the frames
and nuts (42).
(6 and 15). Secure with four capscrews (66), washers (67),
lockwashers (68), and nuts (69).
(c) Install swing joint (30) through support
collar (40) and tighten set screw (39).
(2) Installation of Terminal Board in Motor
Junction Box.
(d) Install a new O-ring (38) between
adapter elbow (29) and outlet elbow (37). Secure the
(a) Install the two nuts (2, fig. 8-7) on
studs
outlet elbow to the adapter elbow with four capscrews (35)
(1) on the terminal board (3). Install the middle capscrew
and lockwashers (36).
(4) and one nut (5) onto the terminal board.
(e) Screw adapter elbow (29) onto swing
(b) Position the terminal board in the motor
joint (30).
junction box (6). Install screw (7), but do not tighten.
Install capacitors (8 and 9) onto screw (7). Be sure
(f) Install axle shaft (34) to adapter elbow
capacitors are installed with marking in position shown in
(29) with capscrew (31), lockwasher (32), and nut (33).
figure 8-7. Tighten screw (7).
(g) Install four spacers (28) onto disc (47)
(c) Install lead with
terminal (11, fig. 8-7)
from motor along with capacitor lead to terminal board.
Secure with screw (10). Install motor lead and capacitor
(h) Install drum (26) over the four spacers
lead to screw (4). Install second nut (5) and tighten.
8-14