(8) Remove twos screws and washers (25 and
(1)
Install oil seal (27) into bore of retainer
24) securing lock ring (24) to retainer (23) and remove
(23).
lock ring (24).
(2)
Install packing (22) in recess of retainer
(9) Using spanner wrench 5120-907-9001,
(23).
remove threaded retainer (23) from housing (7).
(3) Press bearing (20) over shaft of drive gear
Remove packing 122) from retainer (23).
(18) and secure with retaining ring (21).
(10) Remove seal (27) from retainer (23) and
(4) Slide drive gear (18), with bearing (20)
disconnect retaining ring (21) from drive gear (18).
attached, into bore of retainer (23) and secure with
(11) Slide drive gear (18) from retainer (23) and
retaining ring (19).
remove bearing 116) from drive gear (18).
(5) Press bearing (16) into housing (7).
(12) Disconnect retaining ring (19) from retainer
Using spanner wrench 5120-907-9001, screw
(23) and remove bearing (20).
threaded retainer (23) into bore of housing (7).
instructions.
Note.
Refer to paragraph f.
below for
d. Inspection. Check the components for wear
adjustment procedure prior to assembly.
limits a specified in table 4-10.
e. Assembly. During assembly, replace pecking
(6) Position lock ring (24) on retainer (23) and
sets, seas and/or all worn or deformed parts. To
secure with two washers and screws (26 and 25).
assemble the right-angle drive power take-off, refer to
Table 4-10. Repair and Rebuild Standards for
Right-Angle Drive Power Take-off
Wire Limits
Refer-
Direct &
Figure
ence
Point
Size and Fit
General
Number
Letter
Measurement
of New Parts
Support
Depot
(∗)
(∗)
A
ID of retainer bore for bearing
3.1495 to 3.1501
(∗)
(∗)
4-10
B
OD of bearing
3 1491 to 3.1496
(∗)
(∗)
4-10
A-B
Fit of bearing in retainer
0.001T to 0.001L
(∗)
(∗)
4-10
C
ID of bearing
1.5753 to 1.5748
(∗)
(∗)
4-10
D
OD of gearshaft
1.5747 to 1.5752
(∗)
(∗)
4-10
C-D
Fit of gearshaft in bearing
0.0001L to 0.0009L
(∗)
(∗)
4-10
E
OD of gearshift spindle
0.7495 to 0.7500
(∗)
(∗)
4-10
F
OD of bearing
1.0010 to 1.0015
(∗)
(∗)
4-10
G
ID of housing bore for bearing
0.9995 to 1.0005
(∗)
(∗)
4-10
F-G
Fit of bearing in housing
0.0005T to 0.0010T
(∗)
(∗)
4-10
H
OD of gearshaft
1.3779 to 1.3784
(∗)
(∗)
4-10
I
ID of bearing
1.3775 to 1.3780
(∗)
(∗)
4-10
H-I
Fit of gearshaft in bearing
0.0001L to 0.0009L
(∗)
(∗)
4-10
J
OD of bearing
2.8341 to 2.8346
(∗)
(∗)
4-10
K
ID of retainer bore for bearing
2.8346 to 2.8352
(∗)
(∗)
4-10
J-K
Fit of bearing
0.0000 to 0.001L
(7) Press bearing (3) into retaining assembly
threaded retainer assembly (2) into bore of housing (7).
(2) and secure with retaining ring (4).
(10) Install drain plug 117) and plug (5) in
(8) Slide gear (5) into bore of bearing (3) and
housing (7).
secure with retaining ring (1).
(11) Position gasket (8) and plate (14) on
(9) Press bearing (6) into housing (7). Screw
4-24
