C-2
TM 9-4935-481-14-2
(e)
Apply RTV compound MIL-A-46106 to primed areas.
Table 5-2. Cable Connector Repair-Tool Requirements
(f)
Bond the cushioning to the cover immediately. Apply adequate initial pressure to insure intimate
NOTE
contact.
See key at end of table for tool P/N and NSN.
(g)
Allow 24 hours cure time prior to subjecting the bond to excessive movement or any stress.
Cable No.
Ref.
Crimping Tool
Insertion
Extraction
(8)
External painting of metal surfaces is accomplished as follows:
OPN
Desig.
Connector No.
and Positioner
Tool
Tool
(a)
Sand the area to be painted lightly with #120 grit sandpaper.
1W1
P1
P38999-007 or
2 with 4
14
13
10275019
(b)
Wipe clean with MEK and allow to air dry.
MS27467E23B2P
P2
MS3126E22-55P
1 with 5
7
11
(c)
Apply primer MILP23377 CL1 and allow to dry.
P3
P38999-006 or
2 with 4
14
13
MS27467E23B2S
(d)
Apply appropriate color paint MIL-C-22750 CL1 TY_____ and allow to dry.
P4
MS3121E22-55S
1 with 5
7
11
(9)
Metal edge protective grommet material MS 21266-_____ is applied as follows:
1W2
P1
P38999-007 or
2 with 4
14
13
10275017
MS27467E23B2P
(a)
Sand metal surfaces where grommet is to be applied lightly with #120 grit sandpaper.
P2
P38999-006 or
2 with 4
14
13
MS27467E23B2S
(b)
Wipe clean with MEK and allow to air dry.
1W3
P1
MS3126E24-61S
1 with 9
7
11
(c)
Apply adhesive MIS 18636 to both surfaces and bond together.
10275020
P2
MS3126E24-61P
1 with 9
7
11
(d)
Allow to dry.
1W4
P1
MS3121E24-61P
1 with 9
7
11
10275021
(10) Repair of the "canned" voltage regulators (VR1 and VR2) in the DMS-D and DMS-G can be accomplished
utilizing the schematics on figures 4-67 and 4-68, and the parts lists in table 5-4 and 5-5.
1W5
P1
MS3126E14-19S
1 with 9
7
11
10275172
P2
MS3121E14-19P
1 with 9
7
11
(a)
Carefully remove the rubber potting (if applicable).
P3
MS3121E24-61P
1 with 9
7
11
(b) Troubleshoot as required to locate the faulty components. If board removal is necessary, utilize the
1W6
P1
MS3126E14-15P
1 with 8 & 9
6&7
10 & 11
WELLER DS-100 system and remove solder from those pads which hold the board in place. Carefully pry the board up as
10275173
P2
MS3126E10-6S
1 with 9
7
11
required.
1W7
P1
MS27473E22-B2P
2 with 3
14
13
(c)
After repair, resolder the board in place and repot (if applicable), using a suitable potting compound.
10275174
P2
P38999-001 or
2 with 4
12
13
MS27515E23-B2S
1W8
P1
P26482-025 or
1 with 8 & 9
6&7
10 & 11
10276967
MS3126E22-55PW
P2
MS3126E24-61PW
1 with 9
7
11
P3
P38999-003 or
2 with 4
12
13
MS27515E23-B2S
1W11
10275177
P1
MS3126E14-15P
1 with 8 & 9
6&7
10 & 11
5-6
